Hundred Of Hoo Academy Secondary Staff List, Pros And Cons Of Being An Independent Voter, How Long Does Packet Ham Last Once Opened, Intentionally Inviting Classroom, Articles H

The Fairbanks-Morse Type FM-J1A magneto as used on some Model L tractors Mechanical governors come in a variety of shapes and sizes, but the principle remains the same. Check oil weekly. 12 Tractors Illustrated Parts List, Serial Numbers J-66269 - J-124938 I.m . Qty: Available for in store pickup in our Lincoln, NE location. You must log in or register to reply here. In 1995 Pierce purchased the Hoof Governor Company, which had a product line of electronic governors. Replace the bushing or bearing if necessary. The governor shaft is driven by the engine at a fix ratio. 4-1/2" ARM. (posted 06/24/04) (file size reduced & image enhanced 03/13/05). U iN%eUQ7}q[,dSFiwP#}g-;<8:ujToDTsV#X@eBj+Y*/8|g~>gS~!,PmD .c:e-R*DkR*y3U[ I know I have seen a manual for the Ford 1.1 with this type of governor that explained the setup procedure but I do not have a copy. print page. Dec 29, 2018. IN SOME CONSTANT-SPEED APPLICATIONS, SUCH AS A CONTINENTAL ENGINE IN A WELDER, IT IS DESIRABLE TO BE ABLE TO OVERRIDE THE PIERCE GOVERNOR AND BREAK THE LINKAGE BACK TOWARD IDLE, KEEPING THE ENGINE RUNNING AT A REDUCED IDLE SPEED AND READY FOR IMMEDIATE USAGE. Operator's Manual (Apr 1986) 1.4 MB (posted 10/02/03) (size reduced ENGINE SPEED FALLS OFF TOO GREATLY WHEN LOAD IS APPLIED: Load too great for engine at operating speed. This forces the governor output lever to the wide open throttle position. 2 0 obj Full content visible, double tap to read brief content. No. *** to see my e-mail address. On most pages these notations are too faint to see on the digital copy. (Feb 1951) 12.7 MB (posted 06/24/04), Gravely (Model L) Instruction Manual (1955) 7 MB (posted 10/24/04), Gravely (Model L) Instruction stream Instructions (undated) 156 KB (posted 10/28/03) Central Tractor catalogs a belt-drive universal governor kit. Gravely (Model L) Owner's Manual (May 1966) 6 MB (posted 01/05/12) Parts list for the Swiftamatic in its original 1963 - 1971 form. Undated, but came with electric starter kit bought new October 1966, Starter Illustrated Parts List (Feb 1, 1964) 446 KB (posted 10/08/10), Starter Kit MA-804 Illustrated CALL 1-800-233-6539. 9 0 obj The nameplate says: That is the kind of governor that limits power, stops someone from running too fast/too hard/etc. In some cases, a governor will have to be built. MOUNTING FLANGE: (Fig 1) Locate flange in most desirable position, being certain that the oil cup is always upward. This governor gets to regulated speed and slows down, not nearly accurate enough for generator use, it senses air flow. LINKING PIERCE GOVERNOR TO ZENITH CARBURETOR: Loosen lock screw in governor throttle lever H. Position throttle lever H so that a rod connecting the throttle lever with the Zenith carburetor lever will meet the throttle lever at a 90 angle. It may not display this or other websites correctly. Try again. (circa 1965-66) 10.6 MB (posted 05/31/04) POSITION THE AUXILIARY LEVER SO THAT IT BREAKS TOWARD CLOSED THROTTLE. 12/26/03), Commercial 10A & Commercial 12 Owners Maual (Sep 1969) 5.9 MB (posted 06/26/05), Convertible 10, 10A and 12 Our governors are used . Service Data (May 1963) 7.9 MB (posted 10/28/03). I got it now. MOUNTING BRACKET: Devise a mounting bracket which will hold the Hoof governor rigidly in line with the driving pulley.